Logo
Get Estimate

Water Damage Inspection Boise ID Finds Hidden Leaks Fast

Thermal imaging, moisture meters, and same-day answers


When a pipe bursts or your basement floods, a water damage inspection Boise ID homeowners trust tells you exactly where the water went and what it ruined. We use thermal imaging cameras and moisture meters to trace hidden leaks behind drywall, under floors, and inside crawl spaces. You get a written report the same day, plus a clear plan for drying and repairs.

A male inspector in a hard hat conducts a property inspection outdoors with a clipboard.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Boise

What Is Included in the Inspection

Every water damage inspection Boise ID visit includes the full moisture mapping, source confirmation, and same-day written report. Mold sampling and drying equipment are separate services you can add if the findings call for them.

Full Moisture Mapping

We take 12 to 20 readings per room with a Protimeter moisture meter and scan walls and ceilings with a Flir thermal imaging camera. Every reading is logged with its location and depth so you can see exactly where the moisture is.

Source Confirmation

We pressure-test supply lines, check drain fittings, inspect the water heater pan and TPR valve, and look at roof penetrations and window flashing. You get a confirmed source, not a guess, before we leave the property.

Borescope Wall Cavity Check

A borescope camera goes into wall cavities through outlet openings so we can see inside without cutting drywall. This is how we confirm hidden mold behind drywall or wet framing that a surface scan would miss.

Same-Day Written Report

You receive a PDF with photos, moisture readings, a floor plan marked with affected areas, and a recommended drying or repair scope. Reports go out within two hours of the walkthrough, ready to send to your insurance adjuster.

Humidity and Air Check

We log relative humidity in each affected room with an Extech hygrometer and note anything above 60%. High humidity keeps materials wet and feeds mold even after the visible water is gone, so we flag it in the report.

What a Water Damage Inspection Boise ID Covers


A water damage inspection Boise ID is a room-by-room evaluation that maps where moisture entered, how far it spread, and whether mold has started growing. We check baseboards, subfloors, ceiling cavities, crawl spaces, and HVAC closets with a Protimeter moisture meter and a Flir thermal imaging camera. Readings above 16% wood moisture content get flagged. We also use a borescope camera to look inside wall cavities without cutting holes, and a hygrometer to measure relative humidity in each room.

Boise homes take on water in predictable ways. North End bungalows with original galvanized supply lines spring pinhole leaks behind kitchen walls. Boise Bench ranchers get slab leaks that soak carpet for weeks before anyone notices. After a January freeze, we field calls about split copper lines in unheated garages and crawl spaces. If you have been searching for water damage detection near me Boise, that is usually the moment a slow drip has finally shown itself as a stain, a musty smell, or a spike in your water bill.

What to Expect During Your Inspection

Every water damage inspection Boise ID call follows the same five steps. Most homes take two to four hours from arrival to written report.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use

Tools & Equipment

Flir Thermal Imaging Camera

Detects temperature differences behind drywall, under floors, and along slabs to locate hidden moisture without cutting into the structure.

Protimeter Moisture Meter

Takes pin and pinless readings at multiple depths to confirm wet framing, drywall, and subfloor. Readings above 16% wood moisture content get flagged.

Borescope Camera

Looks inside wall cavities through outlet openings so we can see hidden mold behind drywall or wet framing without demolition.

Extech Hygrometer

Logs relative humidity room by room. Anything above 60% keeps materials wet and feeds mold even after visible water is gone.

Zefon Air Sampling Pump

Draws air through an Air-O-Cell spore trap cassette when we need to confirm airborne mold spores after water damage.

Dylos Particle Counter

Measures airborne particle counts in real time to spot elevated spore levels during and after water damage events.

Swab and Tape Lift Kits

Collect surface samples from visible growth for lab identification when species confirmation matters for remediation planning.

Methods & Standards

IICRC WRT Moisture Mapping

We follow IICRC Water Restoration Technician standards for moisture mapping, which means readings at multiple depths and documented drying goals. This gives your insurance adjuster a defensible record of the affected area and the recommended drying scope.

Thermal-First Source Search

We start every inspection with a thermal scan before taking pin readings. The camera shows us where to look, and the moisture meter confirms what we found. This order cuts inspection time and catches hidden leaks that a surface walkthrough would miss.

Air-O-Cell Spore Trap Sampling

When mold is suspected, we run a Zefon pump with an Air-O-Cell cassette for 5 to 10 minutes per sample. Lab results compare indoor spore counts to an outdoor baseline, which is the standard method for confirming hidden mold behind drywall.

HEPA Filtration and Containment

If we find active mold during an inspection, we set up HEPA filters and containment before any sampling or remediation work begins. This keeps spores from spreading to unaffected rooms while the job is in progress.

When to Book a Water Damage Inspection

01

A pipe burst overnight and you mopped up the visible water but the wall still feels cold and damp.

What we do: We run thermal imaging across the wall and take moisture readings at multiple depths. If the cavity is wet, we mark the affected area and recommend drying or drywall removal before mold starts.

→ You know within two hours whether the wall needs to come out or just needs airflow. No waiting, no guessing.

02

You are buying a home in the North End and the inspection report mentions a previous roof leak.

What we do: We inspect the attic sheathing, rafters, and insulation for staining and moisture, then check the ceiling below for hidden damage. If growth is suspected, we take air samples with an Air-O-Cell cassette.

→ You get a clear picture of whether the leak was fixed properly or is still causing damage, before you close.

03

Your water bill jumped 30% and you cannot find a visible leak anywhere in the house.

What we do: We pressure-test supply lines, check the water heater and TPR valve, and scan the slab and walls with thermal imaging. A borescope camera checks wall cavities at outlet openings.

→ We find the source, confirm it with moisture readings, and give you a repair scope you can hand to a plumber.

04

A winter freeze split a copper line in your unheated garage and water ran into the laundry room.

What we do: We trace the water path from the break, map moisture in the laundry room walls and floor, and check the adjoining rooms for hidden spread. The report includes photos and readings for your insurance claim.

→ You get a documented scope the same day, so drying and repairs can start before mold has a chance to grow.

How Water Damage Inspection Runs in Boise

Boise sits in a high-desert climate with cold winters and dry summers, which shapes how water damage happens here. January freezes split copper and PEX lines in unheated garages and crawl spaces. Spring snowmelt and rain push water against foundation walls in the North End and Highlands. Summer irrigation line breaks soak yards and creep into basements on the Bench. The building stock matters too: pre-1950 homes in the North End and East End often have original galvanized supply lines that pinhole from the inside out, while 1960s and 70s ranchers on the Boise Bench are prone to slab leaks. Newer construction in Harris Ranch and Southeast Boise tends to have PEX lines, but we still see failures at fittings and water heater connections. For a water damage assessment in Boise Idaho, we adjust our search pattern to the era and construction type of your home. If you need water damage inspection after storm Boise Idaho weather rolls through, call before the moisture has a chance to spread into adjacent rooms.

Neighborhoods We Serve

  • North End

    Pre-1950 bungalows with original galvanized supply lines. Pinhole leaks behind kitchen and bathroom walls are the most common finding.

  • Boise Bench

    Mid-century ranchers on slab foundations. Slab leaks and under-sink drain failures show up as wet carpet along baseboards.

  • Harris Ranch

    Newer construction with PEX lines. We see fitting failures and water heater connection leaks rather than pipe corrosion.

  • Highlands

    Homes on sloped lots where spring runoff pushes against foundation walls. Basement and crawl space moisture is common after wet springs.

  • Depot Bench

    Older homes with a mix of updated and original plumbing. Attic roof leaks after winter ice dams are a recurring issue.

Local Conditions We Plan For

  • January freezes split lines in unheated spaces

    We see a spike in calls from unheated garages, crawl spaces, and exterior wall runs. Thermal imaging is the fastest way to find the break before water spreads into living space.

  • Spring snowmelt and rain against foundations

    Water pushes through foundation walls and into basements and crawl spaces. We check vapor barriers, sump pits, and floor joists for moisture after every wet spring.

  • Summer irrigation line breaks

    Broken sprinkler lines soak soil against the foundation and can seep into basements. We check the foundation perimeter and interior slab edges for elevated readings.

  • Dry summer air hides slow leaks

    Low humidity dries surface moisture fast, so a slow leak can stay hidden in the wall cavity. Thermal imaging and borescope checks catch what the dry air masks.

North End Pinhole Leak Behind Kitchen Wall

Before

A homeowner noticed a faint musty smell near the kitchen but no visible stain. The wall felt cool to the touch. A previous plumber had checked the visible pipes and found nothing. The galvanized supply line had been pinhole leaking for an estimated three weeks.

After

Thermal imaging showed a cold band running vertically behind the cabinets. Moisture readings confirmed wet framing at 24% wood moisture content. We documented the affected area, and the homeowner had the line replaced and the cavity dried within four days. No mold growth.

Maintenance: Replace remaining galvanized sections in stages and check under-sink cabinets monthly for moisture. A $30 moisture meter is worth keeping on hand for spot checks.

Before

Carpet in the hallway felt damp for two weeks. The water bill had climbed 40% over two months. A slab leak under the foundation was feeding moisture up through the concrete and into the carpet pad. No visible pipe damage anywhere in the house.

After

Thermal imaging traced the temperature difference along the slab. Moisture readings at the baseboard and tack strip confirmed the affected area at 180 square feet. The report documented everything for the insurance claim, and the homeowner had the slab leak repaired and carpet replaced.

Maintenance: Watch your water bill for unexplained increases and check slab edges for warm or damp spots. A thermal scan every two years catches slab leaks early.

Before

After a January freeze, water ran from the garage into the laundry room. The homeowner mopped up the visible water but the laundry room wall stayed cold. A copper supply line in the unheated garage had split at a fitting.

After

We traced the water path from the break, mapped moisture in the laundry room walls and floor, and checked the adjoining hallway for hidden spread. The report showed 45 square feet of affected drywall. Drying started the same day and the wall was dry within three days.

Maintenance: Insulate or heat-trace any supply lines running through unheated spaces. Shut off exterior hose bibs before the first hard freeze and drain the lines.

Water Problems We Solve in Boise Homes

Most water damage starts small and stays hidden until it is expensive. These are the four problems we see most often on Boise water damage inspection calls.

Problem

Hidden leak behind drywall with no visible stain

Framing stays wet for weeks, mold colonizes the cavity, and the first sign is a musty smell or a health complaint. By then the repair scope has tripled.

Our Fix

We scan walls with a Flir thermal imaging camera and confirm with a Protimeter moisture meter. A borescope camera looks inside the cavity through an outlet opening. You get the exact location and a repair scope the same day.

Problem

Crawl space stays wet after a plumbing repair

Ground moisture and poor ventilation keep joists damp, and crawl space mold spreads to the subfloor above. Flooring starts to cup and squeak.

Our Fix

We inspect the vapor barrier, joists, and insulation, then log moisture readings at multiple depths. If growth is present, we sample with a spore trap cassette and recommend encapsulation coatings or a dehumidifier desiccant run.

Problem

Slab leak soaks carpet before anyone notices

Carpet and pad stay wet for weeks, the slab stays cold and damp, and mold grows along the baseboards. Water bills climb without an obvious cause.

Our Fix

Thermal imaging shows the temperature difference along the slab. We confirm with moisture readings at the baseboard and carpet tack strip, then document the affected square footage for your insurance claim.

Problem

Attic mold from a roof leak after a storm

Sheathing and rafters stay wet, insulation loses R-value, and attic mold spreads across the roof deck. The leak may only show up as a ceiling stain months later.

Our Fix

We inspect the roof deck, rafters, and insulation, then check for staining and moisture with a Protimeter meter. If growth is visible, we take tape lift samples and recommend remediation before the next rain.

Why Boise Homeowners Book This Inspection

Why Boise Homeowners Book This Inspection

Water damage gets more expensive every day it sits. These are the four outcomes our customers care about most, and what we deliver on every call.

  • Catch Leaks Early

    A pinhole leak in a copper line can push 10 to 20 gallons a day into your wall cavity. We find it with a thermal imaging camera before the drywall stains, before the baseboards swell, and before mold has a chance to colonize. Early detection keeps a $300 repair from turning into a $6,000 rebuild.

  • Stop Mold Before It Starts

    Mold can begin growing on wet drywall in 24 to 48 hours. Our water damage assessment Boise Idaho service flags wet materials the same day so you can dry them out fast. If growth has already started, we document it with air sampling and spore trap cassettes for your records.

  • Document Everything for Insurance

    We photograph every moisture reading, log the affected square footage, and note the source of the intrusion. That report gives your adjuster the numbers they need. Customers tell us the documentation alone saved them hours of back-and-forth with their carrier.

  • Get a Repair Plan You Can Trust

    You get a written scope: what is wet, what is dry, what needs to come out, and what can stay. No guesswork, no upselling. If your crawl space needs a dehumidifier desiccant run for three days, we say so. If a section of drywall is fine, we tell you that too.

Trained to Find What Others Miss

Our technicians hold IICRC WRT and IICRC AMRT credentials, which means they are trained in water damage restoration standards and mold remediation protocols, not just moisture meter operation. We also carry ACAC CMI and ACAC CMR certifications, EPA Lead-Safe credentials for pre-1978 homes, and OSHA 10 cards. Every inspector is NACHI certified and works under an Idaho state mold license. We have mapped water intrusion in hundreds of Boise homes, from 1920s North End bungalows to new builds in Harris Ranch.

  • IICRC WRT and AMRT certified technicians on every water damage inspection Boise ID call
  • ACAC CMI and CMR credentials for mold assessment and remediation oversight
  • EPA Lead-Safe certified for pre-1978 Boise housing stock
  • Flir thermal imaging and Protimeter moisture meter calibration checked monthly
  • Idaho state mold license and NACHI certified inspector on staff
Get Started Today
Trained to Find What Others Miss

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

What does a water damage inspection cover in Boise ID?
A water damage inspection covers the source search, moisture mapping, and a written report. We check supply lines, drains, water heater connections, roof penetrations, window flashing, crawl spaces, and HVAC closets. We take 12 to 20 moisture readings per room with a Protimeter meter and scan walls with a Flir thermal camera. You get photos, readings, and a repair scope the same day.
How soon should I get water damage inspection in Boise Idaho?
Call within 24 to 48 hours of noticing water. Mold can start growing on wet drywall in that window, and structural damage accelerates fast. If your carpet is wet or a ceiling is sagging, call the same day. We offer same-day water damage inspection Boise ID appointments when you call before 2 p.m., and we can usually be on site within two hours for active leaks.
Does insurance cover water damage inspection in Boise ID?
Most homeowner policies cover the inspection when it follows a covered event like a burst pipe or appliance failure. Sudden and accidental discharge is typically covered; long-term seepage often is not. Our report includes photos, moisture readings, and the confirmed source, which is exactly what adjusters ask for. We recommend calling your carrier before the inspection so you know your deductible and coverage.
Can water damage inspection find hidden leaks in Boise Idaho?
Yes. Hidden leaks are the main reason people book us. We use a Flir thermal imaging camera to spot temperature differences behind drywall, a borescope camera to look inside wall cavities through outlet openings, and a Protimeter moisture meter to confirm wet framing. A slab leak under a Boise Bench rancher or a pinhole leak in a North End supply line shows up on thermal before it shows up as a stain.

Related Services

Mold Inspection

If your water damage inspection turns up wet materials, a mold inspection is the logical next step. We check the same areas for visible growth and musty odors, then document what we find. Boise homes with crawl space or attic moisture are the most common candidates.

View Mold Inspection

Mold Testing

When you need proof of what is growing, mold testing with air sampling pumps and spore trap cassettes gives you lab results. We pair this with water damage findings so your report shows both the moisture source and the mold species present.

View Mold Testing

Air Quality Testing

Water damage often raises indoor humidity and spore counts. Air quality testing with a Dylos particle counter and Air-O-Cell cassettes measures what is floating in your breathing space. Useful after any flood damage inspection Boise Idaho service.

View Air Quality Testing

Black Mold Inspection

Black mold (Stachybotrys) needs sustained moisture to grow. If your water damage inspection found wet drywall that has been damp for a week or more, a black mold inspection checks for the dark staining and confirms with lab samples.

View Black Mold Inspection

Toxic Mold Testing

Some molds produce mycotoxins that affect air quality. Toxic mold testing uses swab and tape lift kits plus air samples to identify species. We recommend it when water damage has sat untreated or when occupants report symptoms.

View Toxic Mold Testing

Mold Remediation

Once water damage is documented and mold is confirmed, remediation removes affected materials and treats the area with antimicrobial solutions. We follow IICRC AMRT protocols and HEPA filtration standards so the job passes post-remediation verification.

View Mold Remediation

Book Your Water Damage Inspection Boise ID Today

Water spreads fast and mold follows within 48 hours. Call now and we will schedule a same-day water damage inspection Boise ID visit, usually within two hours for active leaks. You get a written report the same day with photos, moisture readings, and a repair scope.

Call Now Schedule Inspection

Contact Boise Mold Testing

Ready to schedule an inspection or have questions about mold testing? Call us at +1 866-896-8166 or email info@boisemoldtesting.com. We answer calls 24/7 for emergencies and schedule same-day appointments whenever possible. Our team serves all of Boise and Ada County, including ZIP codes 83702, 83703, 83704, 83705, 83706, and 83709.

Or call us right now at +18668968166 — we answer.

Boise Mold Testing


  • Phone

    +18668968166
  • Address

    Boise, Idaho

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote