Logo
Get Estimate

Mold Remediation Boise ID That Gets Your Home Dry and Safe

Certified mold cleanup for Boise homes, crawl spaces, and attics


When mold shows up behind drywall or under a crawl space vapor barrier, mold remediation Boise ID from our certified team stops it at the source. We handle mold cleanup Boise Idaho for homeowners and property managers across Ada County, from North End bungalows to West Boise rentals. Same-day inspections, upfront pricing, and a written clearance report when we finish.

Intricate pattern of black mold spores on a white background, showcasing decay and organic growth.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Boise

What Our Mold Remediation Service Includes

Every mold remediation Boise ID job includes the core phases: inspection, containment, removal, cleaning, and clearance testing. Add-ons like crawl space encapsulation or HVAC duct cleaning are quoted separately if needed. Here is what is covered in a standard scope.

Full Moisture Investigation

We trace the water source with a moisture meter, thermal imaging camera, and borescope before remediation starts. Fixing the source is the only way to prevent mold from returning. This investigation is included in every job.

Negative Air Containment

We build 6-mil poly containment around the work zone and run HEPA air scrubbers to keep spores from spreading. On a typical 200-square-foot bathroom job, containment setup takes about 90 minutes and stays up until clearance passes.

Contaminated Material Removal

Affected drywall, insulation, carpet padding, and other porous materials are removed, bagged, and disposed of per Idaho waste handling rules. Structural wood is HEPA-vacuumed and treated with antimicrobial solutions.

Surface Cleaning and Encapsulation

Every surface inside containment gets HEPA-vacuumed, wiped, and treated. Exposed framing in crawl spaces and attics receives an encapsulation coating that seals the wood against future moisture. We run a particle counter to confirm spore levels are dropping.

Post-Remediation Clearance Testing

We run air sampling with an Air-O-Cell spore trap cassette and compare indoor counts to an outdoor baseline. You get a written clearance report. If the numbers fail, we re-clean at no additional cost until they pass.

What Mold Remediation Boise ID Actually Involves


Mold remediation Boise ID is the controlled removal of mold growth, contaminated materials, and the moisture source feeding it. It is not wiping walls with bleach. Our crews set up negative air containment, run HEPA filtration, and physically remove affected drywall, insulation, or framing before treating the structure with antimicrobial solutions. We verify moisture with a Protimeter and thermal imaging camera before we ever call a job done.

Boise homes deal with two mold seasons, not one. Spring snowmelt and irrigation saturate crawl spaces; winter roof leaks and bathroom condensation feed attic and ceiling mold. If you have spotted black mold (Stachybotrys) or smelled that musty odor after a water leak, professional mold cleanup near me Boise searches usually start the same way: a moisture problem nobody fixed. We find the source first, then remove the growth.

Our Mold Remediation Process, Step by Step

Every job follows the same sequence, whether it is a 20-square-foot bathroom patch or a full crawl space. Here is what you can expect from the first call to the final clearance report.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use for Mold Remediation

Tools & Equipment

Protimeter and Extech Moisture Meters

Pin-type and pinless meters measure moisture content in drywall, wood, and concrete. We use them to find the water source and confirm the structure is dry before closing up walls.

Flir Thermal Imaging Camera

Thermal imaging reveals temperature differences caused by hidden moisture behind walls and under floors. It lets us find mold without tearing out more material than necessary.

Borescope Camera

A borescope lets us see inside wall cavities and ductwork through a small hole. We confirm mold growth and moisture without large-scale demolition.

SKC Air Sampling Pump with Air-O-Cell Cassette

We draw a known volume of air through a spore trap cassette to measure airborne mold spore counts. This is the same method we use for post-remediation clearance testing.

Dylos Particle Counter

A particle counter gives real-time readings of airborne particles inside containment. We use it to confirm spore levels are dropping before we remove containment.

HEPA Air Scrubbers and Dehumidifier Desiccants

HEPA scrubbers filter spores out of the air inside containment. Desiccant dehumidifiers pull moisture from the structure. Both run continuously until the job passes clearance.

Methods & Standards

IICRC S520 Standard

The IICRC S520 standard defines how mold remediation should be performed, from inspection through clearance. Our technicians are trained to this standard, which covers containment, removal, cleaning, and verification. Following it is what separates a real remediation job from a surface wipe-down.

Negative Air Containment

We build 6-mil poly containment around the work zone and run HEPA air scrubbers to create negative pressure. This keeps spores from migrating into clean areas of your home. Containment stays up until clearance testing passes.

HEPA Vacuuming and Antimicrobial Treatment

Every surface inside containment gets HEPA-vacuumed to remove settled spores, then treated with antimicrobial solutions. Structural wood in crawl spaces and attics receives an encapsulation coating that seals it against future moisture.

Post-Remediation Verification

We run clearance air sampling and compare indoor spore counts to an outdoor baseline. If the numbers pass, we remove containment and issue a written report. If they fail, we re-clean at no additional cost. Most residential jobs clear on the first test.

When to Call for Mold Remediation in Boise

01

A pipe burst in your Boise Bench home over the weekend and water sat for three days before you noticed.

What we do: We inspect the affected area with thermal imaging and moisture meters, set up containment, remove wet drywall and insulation, and run HEPA scrubbers and dehumidifier desiccants until the structure is dry. Then we treat and verify.

→ Most burst-pipe jobs clear within four to six days, and you get a written clearance report for your insurance claim.

02

You are buying a home in the North End and the inspection report flagged mold in the crawl space.

What we do: We perform a full crawl space inspection, collect air and surface samples, and provide a written scope of work with pricing. If remediation is needed, we schedule it before closing.

→ You get a clear remediation estimate the seller can credit at closing, and the crawl space is dry and encapsulated before you move in.

03

Your HVAC system has been running for years without a duct cleaning, and family members are getting sick.

What we do: We inspect the air handler, evaporator coil, and ductwork for mold contamination. If mold is present, we clean the ducts, treat the coil, and replace the filter with a HEPA-rated unit.

→ Airborne spore counts drop to outdoor baseline levels, and allergy symptoms typically improve within a week.

04

A tenant in your West Boise rental reported a musty smell and dark staining on the bathroom ceiling.

What we do: We inspect the bathroom, test for mold species, and remediate the affected area. We document everything with photos and moisture readings for your records.

→ The unit passes clearance testing, and you have documentation showing the issue was resolved properly.

How Mold Remediation Runs in Boise

Boise has two mold seasons, and they hit different parts of the house. Spring snowmelt and irrigation water raise crawl space humidity from March through June. Winter roof leaks and bathroom condensation feed attic and ceiling mold from November through February. Older homes in the North End and Depot Bench often have original crawl space vents that never close, so moisture stays trapped year-round. Newer builds in Harris Ranch and Southeast Boise sometimes have oversized HVAC systems that short-cycle and leave evaporator coils wet. When we scope a mold remediation Boise ID job, we factor in the home's age, foundation type, and ventilation before we quote. If you are searching for mold cleanup in Boise Idaho after a water leak, we can usually inspect the same day and have containment up within 24 hours.

Neighborhoods We Serve

  • North End

    Many homes here are 1920s bungalows with original crawl space vents and minimal insulation. Snowmelt and irrigation water pool under these homes, making crawl space mold the most common call we get.

  • Harris Ranch

    Newer construction with tight building envelopes can trap moisture from cooking, showers, and HVAC condensation. We see attic mold from roof leaks and HVAC mold from oversized systems.

  • Boise Bench

    Basement and crawl space mold after sump pump failures or foundation leaks. Older block walls wick moisture, and remediation often includes encapsulation coatings.

  • Downtown Boise

    Condos and older commercial buildings with shared HVAC systems. Mold in one unit can spread through ductwork, so we inspect the whole system, not just the visible growth.

Local Conditions We Plan For

  • Spring snowmelt and irrigation raising crawl space humidity

    Crawl spaces stay damp from March through June, feeding mold on joists and insulation. We schedule crawl space remediation in late spring and early summer when moisture levels are highest.

  • Winter roof leaks and ice dams

    Attic mold from roof leaks peaks in January and February. We inspect sheathing and rafters for dark staining and musty odors, then remediate before the deck is compromised.

  • Dry summer air pulling moisture through foundation cracks

    Boise summers are dry, but foundation cracks and failed vapor barriers still let ground moisture in. We check crawl spaces year-round, not just after rain.

North End Crawl Space Mold Removal

Before

A 1920s bungalow had visible black mold on floor joists and insulation. The vapor barrier was torn, and moisture readings were above 20 percent. The homeowner noticed a musty smell in the living room above.

After

We removed moldy insulation, HEPA-vacuumed and treated the joists, and installed a new vapor barrier with encapsulation coating. Clearance testing showed spore counts back to outdoor baseline. The job took four days.

Maintenance: Keep crawl space vents closed in winter and check the vapor barrier annually. We recommend a dehumidifier if humidity stays above 60 percent.

Before

A family of four had recurring allergy symptoms and a musty smell from the vents. Inspection found mold on the evaporator coil and in the ductwork. The system had been running without a filter change for over a year.

After

We cleaned the ducts, treated the coil with antimicrobial solution, and replaced the filter with a HEPA-rated unit. Air sampling after remediation showed spore counts dropped by 85 percent compared to the pre-remediation test.

Maintenance: Change the filter every 90 days and schedule annual HVAC inspections. Keep indoor humidity below 50 percent with a dehumidifier during summer.

Before

A sump pump failed during a spring storm, and the basement sat with two inches of water for three days. Mold grew along the block walls and floor joists. The homeowner called us after noticing a musty odor.

After

We extracted standing water, removed affected drywall and insulation, treated the block walls and joists, and ran dehumidifier desiccants for three days. Clearance testing passed on the first try. The job took six days total.

Maintenance: Test the sump pump every spring and install a battery backup. Keep stored items off the floor and run a dehumidifier during humid months.

Mold Problems We Solve for Boise Homeowners

These are the calls we get most often in Boise. Each one has a specific cause and a specific fix. Here is how we handle them.

Problem

Hidden mold behind drywall after a slow leak

By the time you smell it, mold has usually spread several feet beyond the visible stain. Drywall and insulation must be removed, and framing may need treatment.

Our Fix

We use thermal imaging and moisture meters to map the full extent without tearing out more than necessary. Affected drywall comes out, framing gets HEPA-vacuumed and treated, and we verify with clearance testing before closing up.

Problem

Crawl space mold from snowmelt and irrigation

Boise crawl spaces with failed vapor barriers stay damp for months. Joists and insulation grow mold that eventually affects the living space above through the floor.

Our Fix

We remove moldy insulation, treat joists with antimicrobial solutions, and install a new vapor barrier. Encapsulation coatings seal the wood. Most crawl space jobs take three to five days including drying time.

Problem

Attic mold from roof leaks or poor ventilation

Attic mold spreads along roof sheathing and can rot the deck within a season. Once the deck is compromised, you are looking at a roof repair on top of remediation.

Our Fix

We inspect sheathing, rafters, and insulation, remove affected materials, and treat the framing. If ventilation is the root cause, we recommend the fix so the mold does not return next winter.

Problem

Bathroom mold from poor ventilation

Older Boise homes often have undersized exhaust fans that do not move enough air. Mold grows on ceilings, grout lines, and behind the vanity within weeks of a shower.

Our Fix

We remove affected drywall and caulk, treat the framing, and recommend a properly sized exhaust fan. Remediation on a typical bathroom takes two to four days from containment to clearance.

Why Boise Homeowners Choose Our Mold Cleanup

Why Boise Homeowners Choose Our Mold Cleanup

Mold does not stop at the surface. These are the outcomes our Boise customers actually care about after we finish a job.

  • Verified Clearance Results

    We do not just remove visible mold and leave. After remediation we run air sampling with an Air-O-Cell spore trap cassette and a Zefon pump, then compare indoor counts to an outdoor baseline. You get a written report showing the job passed, which matters when you sell a home in Ada County.

  • Same-Day Emergency Response

    Water damage mold grows in 24 to 48 hours. We offer same day mold remediation Boise ID scheduling for active leaks, flooded basements, and burst pipes. Call before noon and a technician can be on-site the same afternoon with drying equipment and containment materials.

  • Source-First Approach

    Removing mold without fixing the moisture is a waste of money. We use a moisture meter, hygrometer, and borescope camera to trace the water source, whether it is a slow supply-line leak, a failed crawl space vapor barrier, or a roof flashing issue, and we document it before remediation begins.

  • Insurance-Ready Documentation

    Most homeowner policies in Idaho cover mold that stems from a sudden covered peril like a burst pipe. We photograph every affected area, log moisture readings, and provide a scope of work your adjuster can process. That paperwork speeds up claims and reduces back-and-forth.

Licensed, Certified, and Verified in Boise

Licensed & Certified

  • IICRC WRT (Water Restoration Technician) — issued by Institute of Inspection, Cleaning and Restoration Certification
  • IICRC AMRT (Applied Microbial Remediation Technician) — issued by Institute of Inspection, Cleaning and Restoration Certification
  • ACAC CMI (Certified Microbial Investigator) — issued by American Council for Accredited Certification
  • ACAC CMR (Certified Microbial Remediator) — issued by American Council for Accredited Certification
  • EPA Lead-Safe Certified — issued by U.S. Environmental Protection Agency

Verified Reviews

Google ★★★★★4.9

They found mold behind our bathroom wall that two other companies missed. Containment went up the same day, and the clearance report showed everything was clean. Fair price and no surprises.

Yelp ★★★★★4.8

Our crawl space was a mess after spring snowmelt. Boise Mold Testing removed the moldy insulation, treated the joists, and installed a new vapor barrier. The musty smell is gone.

BBB ★★★★★4.9

Professional from start to finish. They documented everything for our insurance claim and finished when they said they would. The clearance testing gave us confidence the job was done right.

Frequently Asked Questions About Mold Remediation in Boise

Real answers to the questions we hear most often from local homeowners and property managers.

How much does mold remediation cost in Boise ID?
Most residential mold remediation Boise ID jobs run $1,200 to $6,500 in 2026, depending on square footage and materials affected. A small bathroom patch might be $1,200 to $2,000. A full crawl space with encapsulation typically runs $4,000 to $8,000. Air sampling and clearance testing add $300 to $600. We provide a written scope and price before any work begins.
How long does mold cleanup take in Boise Idaho?
A typical bathroom or kitchen mold cleanup in Boise Idaho takes two to four days from containment setup to clearance testing. Crawl space jobs usually run three to five days because of encapsulation and drying time. Large jobs involving multiple rooms or HVAC systems can take one to two weeks. Lab results add 24 to 48 hours to the timeline.
Does insurance cover mold remediation in Boise ID?
Most Idaho homeowner policies cover mold remediation Boise ID when the mold stems from a sudden covered peril like a burst pipe or appliance failure. Mold from long-term neglect or flooding is usually excluded. We document moisture readings, photos, and a scope of work your adjuster can use. Call your insurer before we start so we can align the paperwork.
What is the mold remediation process in Boise Idaho?
The process has five phases: inspection and testing, containment setup with negative air and HEPA filtration, removal of affected materials, cleaning and encapsulation of structural surfaces, and post-remediation verification with air sampling. Most Boise jobs follow this sequence exactly. We do not skip clearance testing, because that report is your proof the job was done correctly.

Related Mold Services in Boise

Mold Inspection

Before any remediation, a mold inspection identifies where growth is hiding and how far it has spread. We check behind drywall, under sinks, and inside HVAC closets using thermal imaging and borescope cameras. This inspection defines the scope of your remediation job.

View Mold Inspection

Mold Testing

Lab testing tells us which mold species are present, including black mold (Stachybotrys) and toxic mold that produces mycotoxins. We collect air samples with spore trap cassettes and surface samples with swabs or tape lifts. Results guide the remediation plan.

View Mold Testing

Air Quality Testing

Air quality testing measures airborne spore counts inside your home against an outdoor baseline. We use SKC pumps and Air-O-Cell cassettes. This test is the same one we run for post-remediation verification, so you see before-and-after numbers on paper.

View Air Quality Testing

Black Mold Inspection

Black mold (Stachybotrys chartarum) needs constant moisture and cellulose to grow. We inspect crawl spaces, drywall backing, and ceiling tiles where it commonly hides in Boise homes. If we find it, remediation follows immediately with full containment.

View Black Mold Inspection

Toxic Mold Testing

Some mold species release mycotoxins that cause headaches, respiratory issues, and fatigue. We test for toxigenic species using culture media and spore trap slides. If toxic mold is confirmed, our remediation protocol includes enhanced PPE and containment.

View Toxic Mold Testing

Mold Removal

Mold removal is the physical extraction of moldy materials and growth from your home. It is the core phase of remediation. We bag and dispose of contaminated drywall, insulation, and framing per Idaho waste rules, then HEPA-vacuum every surface inside containment.

View Mold Removal

Schedule Mold Remediation Boise ID Today

Mold spreads fast. The sooner we contain it, the less material we have to remove and the lower your bill. Call us for a same-day inspection and a written scope before any work starts. We serve all of Boise and Ada County.

Call Now Book Inspection

Contact Boise Mold Testing

Ready to schedule an inspection or have questions about mold testing? Call us at +1 866-896-8166 or email info@boisemoldtesting.com. We answer calls 24/7 for emergencies and schedule same-day appointments whenever possible. Our team serves all of Boise and Ada County, including ZIP codes 83702, 83703, 83704, 83705, 83706, and 83709.

Or call us right now at +18668968166 — we answer.

Boise Mold Testing


  • Phone

    +18668968166
  • Address

    Boise, Idaho

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote