Full moisture assessment
We check every room, crawl space, attic, and basement with a Protimeter moisture meter, a Flir thermal imaging camera, and a borescope camera. You get a written summary with photos and readings.
Every prevention job starts with a full moisture assessment and ends with verification. What we install depends on what we find, but the core steps are always the same. Here is what is covered in a standard visit.
We check every room, crawl space, attic, and basement with a Protimeter moisture meter, a Flir thermal imaging camera, and a borescope camera. You get a written summary with photos and readings.
We trace moisture back to its source, whether that is a roof leak, a supply-line drip, or ground water. Minor repairs are handled on site. Larger repairs are quoted before we proceed.
Wet materials are dried with commercial dehumidifiers and air movers. Exposed framing and surfaces get an antimicrobial solution to stop any spores from settling while the area dries.
For crawl spaces, we install a sealed vapor barrier and, when needed, an encapsulation coating on joists and piers. This keeps ground moisture out and is the single most effective prevention step in Boise homes.
We size and install dehumidifier desiccants, bath fans, or attic vents based on your home's layout. Correct sizing matters, so we use humidity readings from a hygrometer to pick the right unit.
Before we leave, we re-check moisture with a hygrometer and particle counter. You get a short report showing before and after readings, plus simple maintenance steps to keep things dry.
Mold prevention Boise ID is a moisture-control service that locates the water sources feeding mold growth and closes them off before spores can settle. We inspect the whole house, not just the spot you are worried about. That means checking crawl spaces, attics, basements, bathrooms, kitchens, and HVAC systems with moisture meters, thermal imaging cameras, and borescope cameras. When we find a wet area, we dry it, seal it, and set up the right ventilation or dehumidification so it stays dry through every season.
Boise homes deal with a specific pattern: dry summers followed by wet winters and spring snowmelt. That swing pushes water into crawl spaces and basements, and roof leaks from ice dams feed attic mold. If you have been searching for mold prevention near me Boise ID after a pipe burst or a wet winter, we can help. We also handle mold prevention after flooding Boise Idaho, which is common along the Boise River and in older neighborhoods like the Bench and Depot Bench.
Every job follows the same five steps. You will know what is happening, what it costs, and what to expect at each stage.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Protimeter moisture meter
Measures moisture content in drywall, wood, and concrete. We use it to map wet areas and confirm when materials are dry.
Flir thermal imaging camera
Reveals temperature differences that indicate hidden moisture behind walls and under floors without opening them up.
Borescope camera
Lets us look inside wall cavities and ductwork through a small hole, so we can confirm mold growth without major demolition.
Air-O-Cell spore trap cassette with Zefon pump
Collects airborne spores for lab analysis. We compare indoor and outdoor counts to determine if there is an active mold problem.
Extech hygrometer
Measures relative humidity room by room. We use it to size dehumidifiers and confirm humidity stays below 50% after prevention work.
Dylos particle counter
Counts airborne particles before and after work. Useful for confirming that HEPA filtration and drying have reduced spore levels.
Swab and tape lift kits
Collect surface samples from visible growth. Lab analysis identifies the species, including black mold (Stachybotrys) and toxic mold.
IICRC S520 mold remediation standard
We follow the S520 standard for all mold-related work, from containment to cleaning to verification. It is the industry benchmark and the basis for our written reports.
Crawl space encapsulation
We seal crawl space floors and walls with a vapor barrier and, when needed, an encapsulation coating on framing. This stops ground moisture from rising into the home and is the most effective prevention step in Boise.
HEPA filtration during work
We run HEPA filters and containment during any work that disturbs mold. This keeps spores from spreading to other rooms while we dry or remove affected materials.
Antimicrobial treatment
After drying, we apply an antimicrobial solution to exposed framing and surfaces. This stops any remaining spores from colonizing while the area returns to normal moisture levels.
01
What we do: We check behind walls and under floors with a moisture meter and thermal camera. Even if the surface feels dry, framing and insulation can hold moisture for weeks. We dry any remaining moisture and treat the area.
→ You avoid mold growth that would otherwise show up two to three weeks later, and you have a written record of the moisture readings.
02
What we do: We inspect the crawl space for ground moisture, failed vapor barriers, and joist mold. We install a sealed barrier, treat any affected framing, and add a dehumidifier sized to the space.
→ Crawl space humidity drops below 50%, the musty smell goes away, and the living space above stays drier.
03
What we do: We run a full moisture assessment and air sampling. You get a written report with spore counts, moisture readings, and a prevention plan if needed. This is useful during inspection periods.
→ You know exactly what you are buying or selling, and any prevention work can be scoped and priced before closing.
04
What we do: We test the fan's airflow and check for leaks around the tub and toilet. We upgrade the fan to the correct CFM for the room size and seal any gaps. A humidity sensor switch is an option.
→ The bathroom dries within minutes, and the walls and ceiling stay free of the mold that was starting to form in the corners.
Boise's climate swings hard: dry summers with low humidity, then wet winters and a spring snowmelt that pushes water into crawl spaces and basements. That pattern drives most of the mold work we do. Older homes in the North End, East End, and Depot Bench often have unsealed crawl spaces and original bath fans that move too little air. Newer builds in Harris Ranch and Southeast Boise tend to have tighter envelopes, which means any leak stays trapped and feeds mold faster. We adjust our prevention plan to the house, not a template. For crawl spaces, we seal the ground and add a dehumidifier. For attics, we fix the roof leak and correct ventilation. For basements, we dry, seal, and monitor. If you need mold prevention for crawl spaces Boise Idaho or anywhere in Ada County, we can schedule a visit and give you a written plan.
North End
Older bungalows with unsealed crawl spaces and original bath fans. Ground moisture and poor ventilation are the most common sources we find.
Harris Ranch
Newer, tighter construction. Leaks stay trapped inside walls, so we rely on thermal imaging and moisture meters to find them early.
Boise Bench
Mix of mid-century homes with basements that take on water during spring snowmelt. Drainage and sealing are usually part of the prevention plan.
Southeast Boise
Newer builds with HVAC systems in conditioned space. We check drain pans and ductwork for moisture that can feed mold.
Depot Bench
Older homes near the river corridor. We watch for ground water and roof leaks after wet winters, and test air quality when musty odors are reported.
Spring snowmelt and Boise River flooding
Basements and crawl spaces take on water in March and April. We prioritize drying and sealing during this window so mold does not start within 48 hours.
Winter ice dams on roofs
Ice dams force water under shingles and into attics. We find the leak, dry the sheathing, and correct attic ventilation to prevent repeat damage.
Low summer humidity
Summer air is dry, which slows mold growth. We use this window to install vapor barriers and dehumidifiers so homes are ready for the wet season.
Older housing stock with lead paint
Homes built before 1978 may have lead paint. Our EPA Lead-Safe training means we handle any disturbed materials correctly during prevention work.
Most mold problems start small and get expensive. These are the situations we see most often in Boise, and how we handle them.
Problem
By the time you see staining or smell mustiness, mold has been growing for weeks. Drywall and insulation often need removal, and the leak is still active.
Our Fix
We use thermal imaging and a borescope camera to find the leak without tearing out walls. Once located, we dry the cavity, treat it with antimicrobial solution, and repair the source. Most jobs take one to two days.
Problem
Boise crawl spaces often sit on bare soil. Without a vapor barrier, ground moisture rises into joists and insulation, feeding mold year-round and raising humidity in the living space above.
Our Fix
We install a sealed vapor barrier and, when needed, an encapsulation coating on framing. A crawl space dehumidifier keeps humidity below 50%. This is the most common prevention job we do in Boise.
Problem
Winter ice dams and flashing failures let water into the attic. Wet sheathing grows mold fast, and poor ventilation keeps it damp. Left alone, it spreads across the roof deck.
Our Fix
We find the leak, dry the sheathing, and treat affected areas. Then we correct ventilation with soffit and ridge vents sized to the attic. Most attic jobs are done in two to three days.
Problem
Spring snowmelt and heavy rain push water into basements through cracks and failed drainage. Wet concrete and framing grow mold within 48 hours, and the smell spreads through the house.
Our Fix
We extract standing water, dry the space with commercial equipment, and seal cracks. A dehumidifier and improved drainage keep it dry. We also test air quality after drying to confirm spore levels are normal.
Prevention costs far less than remediation. These are the outcomes our Boise customers see when they act before mold takes hold.
Lower long-term cost
Remediating mold in a crawl space or behind drywall often runs into the thousands. Prevention work like sealing a crawl space, adding a dehumidifier, or fixing a roof leak costs a fraction of that. We help you spend a few hundred now instead of several thousand later.
Healthier indoor air
Mold spores and mycotoxins circulate through your HVAC system and settle in bedrooms. By keeping humidity below 50% and sealing moisture sources, we reduce the spore load in the air your family breathes. Customers with allergies and asthma notice the difference within weeks.
Protects your structure
Mold breaks down drywall, wood framing, and insulation. Once structural lumber is compromised, repairs get expensive fast. Our moisture control to prevent mold Boise approach keeps framing dry and preserves the value of your home for years.
Stops the cycle
Many Boise homes have had mold cleaned up before, only to see it return. That happens when the moisture source is never fixed. We find the leak, the poor ventilation, or the ground-water issue and correct it, so you are not paying for the same cleanup every couple of years.
Google ★★★★★4.9
They found a hidden leak behind our kitchen wall that two other companies missed. The moisture meter and thermal camera work was thorough, and the prevention plan was clear. No mold six months later.
Yelp ★★★★★4.8
Same-day response after our basement flooded. They dried everything, sealed the cracks, and set up a dehumidifier. The written report with moisture readings was helpful for our insurance claim.
BBB ★★★★★4.9
Professional and honest. They tested our attic after an ice dam leak, fixed the ventilation, and did not try to sell us anything we did not need. The follow-up air sampling confirmed the fix.
Our technicians hold IICRC WRT and IICRC AMRT certifications, plus ACAC CMI and ACAC CMR credentials for mold inspection and remediation. We also carry EPA Lead-Safe and OSHA 10 training, which matters in Boise's older housing stock where lead paint is still present. We use calibrated instruments from Protimeter, Flir, Extech, and Dylos on every job, and we follow the IICRC S520 standard for mold work. That combination of certification, tooling, and local experience is why Boise homeowners call us when moisture shows up.
Real answers to the questions we hear most often from local homeowners and property managers.
A full mold inspection is often the first step before prevention work. We check crawl spaces, attics, basements, and HVAC systems for visible growth and hidden moisture, then give you a written report with photos and recommendations for Boise homes.
View Mold InspectionWhen we need to confirm what is growing, mold testing with air sampling and surface samples identifies the species. This matters for black mold (Stachybotrys) and toxic mold concerns. Results guide the prevention plan we build for your Boise property.
View Mold TestingAir quality testing measures spore counts inside and outside your home. If indoor counts are higher than outdoor, we have a moisture problem to solve. This test pairs well with prevention work and post-remediation verification in Boise.
View Air Quality TestingBlack mold (Stachybotrys) needs sustained moisture to grow. Our black mold inspection targets the wet areas where it appears, like behind drywall and under sinks. If we find it, we build a prevention plan that removes the moisture source for good.
View Black Mold InspectionSome molds produce mycotoxins that affect health. Toxic mold testing identifies those species through lab analysis. If your Boise home has had water damage or a chronic leak, this test tells you what you are dealing with before prevention work begins.
View Toxic Mold TestingWhen mold is already established, remediation removes it following IICRC S520 standards. We contain the area, remove affected materials, and clean surfaces. Prevention work after remediation keeps the problem from returning in your Boise home.
View Mold RemediationReady to schedule an inspection or have questions about mold testing? Call us at +1 866-896-8166 or email info@boisemoldtesting.com. We answer calls 24/7 for emergencies and schedule same-day appointments whenever possible. Our team serves all of Boise and Ada County, including ZIP codes 83702, 83703, 83704, 83705, 83706, and 83709.
Phone
+18668968166Address
Boise, Idaho
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available