Logo
Get Estimate

Toxic mold testing Boise ID that finds what your nose can't

Lab-backed mycotoxin testing in Boise Idaho, results in 24-48 hours


If your Boise home smells musty, your allergies won't quit, or you've had a leak, toxic mold testing Boise ID tells you exactly what's growing and where. We run air sampling, moisture mapping, and surface swabs on the same visit, then send samples to an accredited lab. Homeowners, renters, and property managers across Ada County call us when they need answers, not guesses.

A scientist in protective gear conducts research at a waste site during sunset.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Boise

What's included in every toxic mold inspection

Every toxic mold testing Boise ID job includes a full on-site inspection, lab analysis, and a written report. We don't charge extra for the basics. Here's what you get, and what's available as an add-on if your situation calls for it.

Full visual inspection

We walk the entire property, including crawl space, attic, basement, bathrooms, kitchen, and HVAC closet. We check for visible growth, water staining, and conditions that support mold. This takes 45-60 minutes on a typical Boise home.

Moisture mapping

A Protimeter moisture meter and Flir thermal imaging camera let us find damp areas behind walls and under floors without cutting anything open. We log readings room by room and flag anything above normal.

Air sampling

We run an SKC air sampling pump with Air-O-Cell spore trap cassettes indoors and take an outdoor control sample. This tells us whether indoor spore levels are elevated compared to what's naturally outside.

Surface sampling

If we find visible growth, we take swabs or tape lifts and send them to the lab for species identification. This is how we confirm black mold (Stachybotrys) versus less concerning species.

Written lab report

You get a report with photos, lab data, species identification, spore counts, and a plain-English summary. We include remediation recommendations if needed and prevention steps regardless.

Phone walkthrough

After you receive the report, we schedule a 15-minute call to go over findings and answer questions. No extra charge. If you need us to talk to your landlord, insurance adjuster, or remediation contractor, we can do that too.

What toxic mold testing Boise ID actually involves


Toxic mold testing Boise ID is a diagnostic service that measures airborne spores, surface contamination, and moisture conditions to identify harmful mold like Stachybotrys and its mycotoxins. We don't just look at a dark spot and guess. We use a moisture meter and thermal imaging camera to trace water behind drywall, an air sampling pump with Air-O-Cell spore trap cassettes to capture what you're breathing, and swab or tape lift kits on visible growth. Every sample goes to an accredited lab, and you get a written report with species, spore counts, and a clear next step.

Boise homes give mold plenty of openings. Winter inversions trap humidity indoors, snowmelt and spring rain push water against foundations, and the Valley's older North End and Depot Bench houses often have crawl spaces with no vapor barrier. If you've had a burst pipe, roof leak, or flooding, a toxic mold inspection after water damage Boise ID is worth scheduling within 48 hours. We also get calls from renters who want mycotoxin testing in Boise Idaho before they sign another lease or escalate a landlord complaint.

How our Boise toxic mold testing process works

Every job follows the same five steps. You'll know what's happening, who's doing it, and when you'll get results. Most residential inspections take 60-90 minutes on site.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and methods we use for mold testing

Tools & Equipment

Protimeter moisture meter

Measures moisture content in drywall, wood, and concrete. Pin and pinless modes let us check surfaces and behind them. Readings above 16% on wood indicate conditions that support mold growth.

Flir thermal imaging camera

Detects temperature differences that reveal hidden moisture, air leaks, and missing insulation. We use it to find wet spots behind walls without cutting them open.

SKC air sampling pump with Air-O-Cell cassettes

Draws a known volume of air through a spore trap cassette. The lab counts spores per cubic meter and identifies species. This is the core of our air quality testing.

Zefon and 3M sample cassettes

Industry-standard spore trap and culture media cassettes. We use them for both air and surface sampling. Lab compatibility is universal, so results are consistent.

Borescope camera

A thin camera on a flexible cable that lets us see inside wall cavities, ductwork, and crawl spaces without demolition. We confirm visual growth before recommending any wall be opened.

Extech hygrometer

Measures relative humidity and dew point. We log readings room by room. Anything above 60% RH is a mold risk, especially in sealed winter homes.

Dylos particle counter

Counts airborne particles in real time. Useful for detecting elevated particulate levels that suggest mold, dust, or HVAC contamination. We use it alongside spore trap sampling.

Methods & Standards

IICRC S520 mold assessment standard

The industry standard for mold inspection and remediation. We follow it for condition assessment, sampling protocol, and report formatting. Reports that follow S520 are accepted by insurance companies and remediation contractors.

Outdoor control sampling

We always take an outdoor air sample alongside indoor samples. This gives us a baseline for what's naturally in Boise's air. Indoor spore counts are compared to outdoor levels to determine if there's a problem.

Moisture mapping

We create a room-by-room map of moisture readings using the Protimeter and thermal camera. This shows us where water is present, how far it's spread, and whether conditions are dry enough to prevent future growth.

Surface sampling with swabs and tape lifts

When we find visible growth, we take a swab or tape lift and send it to the lab for species identification. This confirms whether it's Stachybotrys, Cladosporium, Aspergillus, or another species.

Post-remediation verification (clearance testing)

After remediation, we return to take air samples and confirm spore counts have returned to normal. This is called clearance testing, and it's your proof the job was done correctly.

When to schedule toxic mold testing in Boise

01

You had a pipe burst or appliance leak over the winter and dried it with fans and a dehumidifier.

What we do: We inspect the area with a moisture meter and thermal camera, then take air samples to check for elevated spores. If mold has started behind the drywall, we'll find it before it spreads.

→ You either get confirmation that the area is clean or a documented scope for remediation. Either way, you stop worrying and start acting.

02

Your rental has a musty smell and your landlord says it's 'just old building smell.'

What we do: We perform toxic mold testing for renters Boise Idaho, document findings in a written report, and provide lab data you can share with your landlord or a tenant rights organization.

→ You have objective evidence. Most landlords take action once they see a lab report. If they don't, you have documentation for your next step.

03

You're buying a home in the North End or Depot Bench and the inspection report mentioned 'possible moisture issues.'

What we do: We run a full toxic mold inspection Boise ID with air sampling, moisture mapping, and surface testing in any suspect areas. The report is formatted for real estate transactions.

→ You know exactly what you're buying. If mold is present, you can negotiate the price, request remediation, or walk away with your earnest money.

04

Your HVAC system has a musty smell when it kicks on, and you've noticed more allergies indoors.

What we do: We inspect the air handler, evaporator coil, and accessible ductwork for HVAC mold contamination. We take air samples at supply vents and in living spaces to measure what's circulating.

→ You get a clear answer on whether your HVAC is the problem and what it takes to fix it. Sometimes it's a coil cleaning. Sometimes it's duct replacement. We tell you which.

05

You finished a basement remodel and now the space smells damp, even though you used a dehumidifier.

What we do: We check for basement mold after flooding or construction moisture, inspect walls and flooring, and run air sampling. A hygrometer reading tells us if humidity is still too high.

→ We identify whether the issue is active mold growth, residual moisture, or a ventilation problem. You get a targeted fix, not a blanket remediation quote.

How toxic mold testing works in Boise specifically

Boise's climate creates specific mold risks. Winter inversions trap moisture indoors, and homes sealed tight for energy efficiency don't get enough air exchange. Spring snowmelt and rain push water against foundations, especially in older neighborhoods like the North End and Depot Bench where crawl spaces often lack vapor barriers. Summer air conditioning creates condensation in ductwork and on evaporator coils, which is a common source of HVAC mold contamination. We see a spike in calls after every major freeze-thaw event and after any prolonged rain. If you're searching for mycotoxin testing in Boise Idaho, you probably have one of these scenarios: a leak you're not sure was dried, a musty smell that won't go away, or health symptoms that improve when you leave the house. We also work with a lot of renters who need documentation for landlord disputes. Our reports are written to hold up with property managers, insurance adjusters, and in some cases, legal proceedings. We know Boise's building stock, from downtown condos to mid-century ranch homes to new construction in Harris Ranch, and we know where mold hides in each.

Neighborhoods We Serve

  • North End

    Older homes with crawl spaces and minimal vapor barriers. High water table in some areas. We inspect a lot of North End crawl spaces that have never been sealed.

  • Depot Bench

    Mid-century homes with basements that seep during spring snowmelt. We often find mold on basement walls and stored items.

  • Boise Bench

    Mix of older and newer construction. Rental density is high, so we do a lot of pre-lease testing and landlord documentation.

  • Harris Ranch

    Newer construction with tight building envelopes. HVAC mold contamination is more common here because homes don't breathe as much.

  • Downtown Boise

    Condos and apartments with shared HVAC systems. When one unit has mold, adjacent units can be affected. We test common areas and individual units.

Local Conditions We Plan For

  • Winter inversions trap humidity indoors

    Boise's winter inversions keep cold, moist air trapped near the ground. Homes sealed for energy efficiency don't exchange air, so indoor humidity climbs. We see more mold calls in January and February than any other month.

  • Spring snowmelt and rain against foundations

    March through May, snowmelt and rain push water against foundations and into crawl spaces. If drainage is poor, water sits. Mold starts within 48 hours. We schedule a lot of post-spring inspections.

  • Summer AC condensation in ductwork

    Air conditioning creates condensation on evaporator coils and in ductwork. If the system isn't maintained, mold grows inside the ducts and circulates through the house. We inspect HVAC systems year-round but see more problems in July and August.

  • Older homes with no vapor barrier

    Many Boise homes built before 1980 have crawl spaces with bare dirt floors. Without a vapor barrier, ground moisture rises into the crawl space and up into the house. This is one of the most common findings in our inspections.

Hidden mold behind drywall in North End home

Before

A homeowner had a roof leak repaired but never tested for mold. Six months later, her son's asthma worsened. A musty smell in his bedroom was the only clue. Visual inspection showed nothing.

After

Thermal imaging found moisture behind the bedroom drywall. Air sampling confirmed elevated Stachybotrys spores. We documented the findings, and remediation removed the affected drywall. Post-remediation testing showed spore counts back to normal.

Maintenance: Keep gutters clean, check the roof after every storm, and retest if you ever have a leak. A $350 test is cheaper than six months of breathing mold.

Before

A property manager noticed a musty smell in one unit. The crawl space had no vapor barrier and standing water after spring rain. Tenants complained of allergies but no one had tested.

After

We found mold on floor joists and subfloor. Air sampling showed elevated spore counts in both units. The owner installed a vapor barrier and had the crawl space remediated. Clearance testing confirmed the fix.

Maintenance: Install a vapor barrier, run a dehumidifier in the crawl space during spring and summer, and inspect annually. Vapor barriers cost $1,500-$3,000 and prevent $10,000+ in damage.

Before

A family in a 5-year-old home had allergies that wouldn't quit. The house was tight and energy-efficient. Every time the AC kicked on, the smell got worse. No visible mold anywhere.

After

We inspected the air handler and found mold on the evaporator coil. Air samples at supply vents showed elevated spores. The coil was cleaned, ducts were sanitized with antimicrobial solutions, and HEPA filters were installed. Symptoms improved within a week.

Maintenance: Change HEPA filters every 3 months, have the evaporator coil cleaned annually, and keep indoor humidity below 55%. A $200 annual HVAC service prevents a $3,000 duct replacement.

Mold problems we solve for Boise homeowners

Most people call us because something feels wrong and they can't see why. Maybe there's a smell. Maybe someone in the house is sick. Maybe there was a leak and they're not sure it was handled correctly. Here's what we typically find and fix.

Problem

Musty smell with no visible mold

That smell means mold is growing somewhere you can't see. It could be behind drywall, under flooring, or inside the HVAC system. Ignoring it lets the problem spread and keeps you breathing spores.

Our Fix

We use thermal imaging and moisture meters to trace the source, then air sampling to confirm what's in the air. Most hidden mold gets found within an hour. You get lab data showing exactly what species is present and where it's concentrated.

Problem

Health symptoms that won't go away

Headaches, sinus congestion, coughing, and asthma flare-ups that improve when you leave the house often point to indoor air quality problems. Without testing, you're guessing.

Our Fix

Health hazard mold testing Boise ID gives you objective data to bring to your doctor. We document spore counts and species so a medical professional can assess whether your symptoms line up with mold exposure.

Problem

Recent water damage you're not sure was dried properly

Mold starts growing within 24-48 hours of water intrusion. If a leak or flood wasn't dried with commercial equipment, mold is likely already forming behind walls or under floors.

Our Fix

A toxic mold inspection after water damage Boise ID confirms whether mold has started and how far it's spread. We check moisture levels, take air samples, and document conditions for insurance. If it's clean, we tell you. If it's not, you have proof.

Problem

Buying or renting a home with a mold history

Sellers and landlords don't always disclose mold problems. Moving into a contaminated home means you inherit the cleanup cost and the health risk.

Our Fix

Pre-purchase and pre-lease testing gives you leverage. We inspect, sample, and report. If mold is found, you can negotiate remediation, walk away, or budget for the fix. Our reports are written for real estate transactions.

Problem

Crawl space or attic mold you discovered yourself

Crawl space mold and attic mold from roof leaks are common in Boise. DIY cleanup without testing can spread spores and miss the source. You need to know what species you're dealing with.

Our Fix

We inspect the space, take surface samples, and run air sampling in adjacent living areas. You get species ID, spore counts, and a remediation scope. If it's a small problem, we'll tell you how to handle it yourself.

Why Boise homeowners book toxic mold testing

Why Boise homeowners book toxic mold testing

Mold isn't a cosmetic problem. It's a health and structural issue, and the only way to handle it correctly is to know what species you're dealing with and how far it has spread. Here's what you actually get when you book us.

  • Answers in 24-48 hours

    Most labs return spore trap and culture results within one to two business days. You get a written report listing species, spore counts per cubic meter, and whether levels are elevated compared to an outdoor control sample. No vague 'looks like mold' language.

  • Hidden mold found fast

    A Flir thermal imaging camera and Protimeter moisture meter let us see temperature and moisture differences behind drywall, under flooring, and inside wall cavities without tearing your house apart. We confirm with a borescope camera before we ever recommend opening a wall.

  • Health-hazard documentation

    If you're dealing with headaches, sinus issues, or asthma flare-ups, health hazard mold testing Boise ID gives you a paper trail. Our reports are formatted for doctors, landlords, insurance adjusters, and remediation contractors who need documented evidence, not opinions.

  • Clear scope before remediation

    Remediation without testing is a shot in the dark. Knowing whether you have black mold (Stachybotrys) in one corner or HVAC mold contamination across three rooms changes the scope, the cost, and the cleanup method. Testing first saves money.

Frequently asked questions about toxic mold testing in Boise

Real answers to the questions we hear most often from local homeowners and property managers.

What is toxic mold testing in Boise ID?
Toxic mold testing in Boise ID is a lab-based inspection that identifies mold species, measures airborne spore counts, and checks for mycotoxins produced by molds like Stachybotrys. We collect air samples, surface swabs, and moisture readings, then send everything to an accredited lab. You get a written report with species, counts, and recommendations. It's not the same as a visual inspection, because it tells you what's actually in the air and on surfaces, not just what you can see.
How much does mycotoxin testing cost in Boise Idaho?
Most residential mycotoxin testing in Boise Idaho runs $350 to $850 depending on how many samples you need and whether you want a specific mycotoxin panel. A basic air sample package with 3-4 samples and an outdoor control starts around $350. Larger homes, crawl space or attic add-ons, and specialty panels push the price higher. We quote the exact price before we schedule, and there's no charge for the initial phone assessment.
Can toxic mold make you sick in Boise ID?
Yes. Exposure to mold spores and mycotoxins can trigger sinus congestion, headaches, coughing, asthma flare-ups, and skin irritation. People with allergies, asthma, or compromised immune systems are more sensitive. If you've been feeling off and your home has a musty smell or a history of water damage, testing gives you objective data to bring to your doctor. We can't diagnose illness, but we can document what's in your indoor air so a medical professional has something concrete to work with.
How long do toxic mold test results take in Boise Idaho?
Standard air sampling and surface swab results come back in 24 to 48 hours. Culture-based tests that require incubation can take 5 to 7 days. Mycotoxin-specific panels vary by lab and may run 3 to 10 business days. We ship samples the same day we collect them and email your report as soon as the lab releases it. If you need results faster for a real estate deadline or insurance claim, tell us when you book and we'll flag the order as rush.

Other mold and moisture services we offer

Mold Inspection

A full visual and moisture assessment of your Boise property. We check crawl spaces, attics, bathrooms, and HVAC systems for signs of growth. Often paired with toxic mold testing Boise ID when you want both a physical inspection and lab confirmation.

View Mold Inspection

Mold Testing

Air, surface, and bulk sampling to identify mold species and spore counts. This is the broader category that includes toxic mold testing. If you're not sure which test you need, start here and we'll recommend the right panel for your Boise home.

View Mold Testing

Air Quality Testing

Measures airborne particles, spores, and allergens using a Dylos particle counter and air sampling pump. Useful when you suspect HVAC mold contamination or want a baseline before buying a Boise home. Pairs well with mycotoxin testing Boise Idaho.

View Air Quality Testing

Black Mold Inspection

Targeted inspection for Stachybotrys chartarum, the black mold that produces mycotoxins. We look in the wet, dark places it prefers: behind drywall, under sinks, in crawl spaces. Confirmation requires lab testing, which we include.

View Black Mold Inspection

Mold Remediation

We don't perform remediation, but we can refer you to licensed contractors and verify their work afterward. Post-remediation verification testing confirms the cleanup worked. That's how you know the job is actually done.

View Mold Remediation

Mold Removal

Physical removal of mold-contaminated materials. If testing shows significant growth, removal is usually the next step. We document the extent so your removal contractor knows exactly what to tear out and what to treat.

View Mold Removal

Book toxic mold testing Boise ID before the problem spreads

Mold doesn't stop at one wall. If you've had water damage, a musty smell, or unexplained health symptoms, get answers this week. Call us, describe what's going on, and we'll quote the job before we schedule. Same-week appointments available across Ada County.

Call Now Schedule Inspection

Contact Boise Mold Testing

Ready to schedule an inspection or have questions about mold testing? Call us at +1 866-896-8166 or email info@boisemoldtesting.com. We answer calls 24/7 for emergencies and schedule same-day appointments whenever possible. Our team serves all of Boise and Ada County, including ZIP codes 83702, 83703, 83704, 83705, 83706, and 83709.

Or call us right now at +18668968166 — we answer.

Boise Mold Testing


  • Phone

    +18668968166
  • Address

    Boise, Idaho

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote