Logo
Get Estimate

Mold removal Boise ID that gets your home dry and clean

Licensed crews, same-day assessments, and containment done right


When you need mold removal Boise ID homeowners can actually trust, we show up with moisture meters, thermal cameras, and HEPA equipment, not a spray bottle and a promise. Whether it's black mold behind drywall in the North End or crawl space growth in the Bench, we find the source, remove the growth, and verify the air is clean before we pack up. Most jobs are quoted the same day you call.

A worker in protective gear uses a disinfectant spray indoors.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Boise

What is included in mold removal service

Every mold removal job we run includes the full scope from inspection through clearance testing. We do not nickel-and-dime for containment, HEPA filters, or lab samples. If the job needs additional work beyond the original scope, we stop and quote it before continuing.

On-site inspection and moisture mapping

A technician inspects the property with a moisture meter, hygrometer, and thermal imaging camera. We map where moisture is present and where mold is likely growing. This visit runs 60 to 90 minutes and is included in every job quote.

Air and surface testing

We collect air samples with an SKC pump and Air-O-Cell cassettes, plus swab or tape lift samples where growth is visible. Lab results come back in 24 to 48 hours. Testing before removal prevents tearing out materials that do not need to come out.

Containment and HEPA filtration

We build 6-mil poly barriers and run negative-air HEPA scrubbers to keep spores from spreading. HVAC registers get sealed. This step is what separates a professional job from a DIY attempt that spreads mold through the house.

Removal and disposal

Contaminated drywall, insulation, carpet padding, and other porous materials get bagged and hauled out. Framing and hard surfaces get scrubbed and treated with EPA-registered antimicrobial solutions. We follow IICRC S520 on every removal.

Post-remediation verification

After removal, we run a particle counter and take clearance air samples. You get a written lab report showing indoor spore counts at or below outdoor baseline. If numbers are high, we keep working until they are not.

Moisture source repair or referral

Mold comes back if the water source stays. We repair what we can, like ventilation issues or minor plumbing, and refer you to a licensed plumber or roofer for the rest. Every job ends with a written plan for keeping the space dry.

What mold removal Boise ID really involves


Mold removal Boise ID is the physical removal of fungal growth, contaminated materials, and the moisture source feeding it, followed by air scrubbing and verification. It is not a bleach wipe-down. We set up negative-air containment, run HEPA filtration, pull damaged drywall or insulation, treat framing with antimicrobial solutions, and confirm spore counts dropped with post-remediation air sampling. Skipping any step usually means the mold comes back within a season.

In Boise, the calls we get most are crawl space mold after a wet spring, attic mold from a slow roof leak, and bathroom mold from poor ventilation. Ada County's dry summers do not save you if a supply line drips behind a cabinet for three weeks. If you have been searching mold removal near me Boise ID and getting generic answers, the fix is finding the water first. We do that with a moisture meter and thermal imaging camera before we touch a single panel.

How our mold removal process works

Every job follows the same five steps, whether it is a 20-square-foot bathroom patch or a full crawl space. Here is what you can expect from the first phone call to the final lab report.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and methods we use on every job

Tools & Equipment

Protimeter moisture meter

Measures moisture content in drywall, wood, and concrete to find hidden water sources feeding mold growth. We use it on every inspection.

Flir thermal imaging camera

Reveals temperature differences behind walls and under floors that indicate moisture or air leaks. It lets us find mold without cutting exploratory holes.

Borescope camera

Looks inside wall cavities, ductwork, and crawl spaces through small access points. We use it to confirm growth before recommending removal.

SKC air sampling pump with Air-O-Cell cassettes

Collects air samples for lab analysis. The cassettes capture spores on a slide that a lab counts and identifies. Results come back in 24 to 48 hours.

HEPA air scrubbers

Filter airborne spores during removal. We run them continuously inside containment to keep spores from escaping into the rest of the house.

Particle counter

Gives real-time readings of airborne particle counts. We use it to confirm clearance before taking final air samples.

Swab and tape lift kits

Collect surface samples from visible growth for lab identification. Tape lifts work well on dry surfaces; swabs work better on wet or porous materials.

Methods & Standards

IICRC S520 mold remediation standard

The industry standard for mold removal, covering containment, removal, cleaning, and verification. We follow it on every job, from a small bathroom patch to a full crawl space. It is also what insurance adjusters expect to see in documentation.

Negative-air containment

We build 6-mil poly barriers around the work area and run HEPA scrubbers to create negative pressure. That means air flows into the containment, not out, so spores stay where they started. This is the single most important step for preventing cross-contamination.

Antimicrobial treatment of framing

After removing contaminated materials, we scrub and treat exposed framing with EPA-registered antimicrobial solutions. This kills remaining spores on hard surfaces and gives the wood a clean start before reconstruction.

Post-remediation verification (PRV)

After removal, we run a particle counter and take clearance air samples. Indoor spore counts must be at or below outdoor baseline. You get a written lab report. If numbers are high, we keep working at no extra charge.

Moisture source correction

Mold removal only lasts if the water source is fixed. We repair what we can, like ventilation issues or minor plumbing, and refer you to a licensed plumber or roofer for the rest. Every job ends with a written plan for keeping the space dry.

When to call for mold removal

01

You had a pipe burst or appliance leak and the area stayed wet for more than 48 hours.

What we do: We inspect with moisture meters and thermal cameras to see how far the water traveled. If mold has started, we scope the removal and quote a flat price. If it has not, we can often dry the space and skip removal entirely.

→ You either get a clean bill of health or a clear scope and price. Either way, you know where you stand within a day.

02

You smell something musty in the basement or crawl space but cannot see any growth.

What we do: We run air sampling with an SKC pump and Air-O-Cell cassettes to check spore counts. If levels are elevated, we use a borescope camera to find the source without cutting into walls or floors.

→ You get lab results in 24 to 48 hours and a clear answer on whether you have a mold problem or just a humidity issue.

03

You are buying or selling a home in Boise and the inspection flagged possible mold.

What we do: We do a targeted inspection and testing to confirm species and extent. If removal is needed, we quote a flat price. The clearance report at the end is documentation that the issue was handled correctly.

→ Buyers and sellers get a clean report to close the deal, and you avoid re-inspection delays.

04

Your family has unexplained allergies or respiratory symptoms that get worse at home.

What we do: We test the air for mold spores and compare indoor levels to outdoor baseline. If specific species show up, we inspect the likely source areas, like the HVAC, attic, or crawl space.

→ You get a lab report identifying what is in the air and a plan to remove it. Many clients see symptom improvement within a week of clearance.

05

You see visible black mold on drywall, ceiling tiles, or framing.

What we do: We inspect and test to confirm whether it is Stachybotrys or another species. Black mold removal Boise ID jobs require containment and careful handling because disturbing it releases spores. We scope the removal and quote before starting.

→ The growth is removed, the framing is treated, and clearance testing confirms the air is clean.

How mold removal runs in Boise specifically

Boise has a dry climate, but that does not mean mold is rare here. Our wet springs and occasional winter freeze-thaw cycles push water into crawl spaces and attics, and older homes in the North End and Depot Bench often have plumbing and drainage systems that were not built for modern use. We see a spike in crawl space mold calls every April and May after snowmelt, and another wave in January when supply lines freeze and burst. Attic mold usually shows up after a roof leak has been dripping for weeks. Newer builds in Harris Ranch and Warm Springs are tighter, which means moisture from cooking, showers, and HVAC condensation has fewer places to escape. If you have been searching mold elimination in Boise Idaho and getting generic advice, the fix is almost always local: find the water, remove the growth, and correct the moisture path. We do that with the same equipment and the same verification standard on every job, whether it is a 20-square-foot bathroom or a full crawl space.

Neighborhoods We Serve

  • North End

    Older homes with original plumbing and crawl spaces. Slow leaks under kitchens and bathrooms are common, and mold often hides behind original plaster and lath.

  • Boise Bench

    Mid-century homes with crawl spaces that trap moisture from wet springs. We see a lot of joist and subfloor mold here after April and May.

  • Harris Ranch

    Newer, tighter construction that holds humidity. HVAC and attic mold calls are more common than crawl space issues in this area.

  • Depot Bench

    Mix of older and renovated homes. Renovations sometimes cover up old leaks, and we find hidden mold behind new drywall during inspections.

  • Warm Springs

    Homes near the foothills get more roof and attic moisture from snowmelt and tree debris. Attic mold after a slow roof leak is a frequent call.

Local Conditions We Plan For

  • Wet spring snowmelt and crawl space flooding

    April and May are our busiest months for crawl space mold. Water pools under homes, insulation stays wet, and mold starts within a week. We prioritize these calls because the damage gets worse fast.

  • Winter freeze-thaw cycles and burst supply lines

    January and February bring a wave of burst pipe calls. Water behind walls feeds mold within 48 hours. We run emergency response for these jobs, including after-hours.

  • Dry summer air that hides moisture problems

    Boise summers are dry enough that wet spots can seem to dry out. But moisture trapped behind walls or under floors stays put. We use moisture meters and thermal cameras to find what the dry air is hiding.

  • Tight modern construction with limited ventilation

    Newer homes in Harris Ranch and Southeast Boise hold humidity from showers, cooking, and HVAC condensation. Without proper ventilation, that moisture feeds mold in bathrooms and attics.

North End kitchen cabinet mold removal

Before

A slow supply line leak under a kitchen sink went unnoticed for about three weeks. The cabinet base, back panel, and adjacent drywall were covered in black mold. The homeowner noticed a musty smell but could not see the growth until we pulled the cabinet out.

After

We removed the affected cabinet base and drywall, treated the framing with antimicrobial, and ran HEPA scrubbers for 24 hours. Clearance testing showed indoor spore counts at outdoor baseline. The whole job took two days, and the homeowner had the cabinet rebuilt the following week.

Maintenance: We recommended a moisture sensor under the sink and a yearly check of supply lines. Small leaks are the most common cause of kitchen mold, and a $30 sensor catches them before they become a $3,000 job.

Before

After a wet spring, the crawl space had standing water and mold across the joists and subfloor. Insulation was soaked and falling down. The homeowner noticed musty odors in the living room and called us after a home inspection flagged the issue.

After

We pumped out the water, removed the contaminated insulation, treated the joists and subfloor with antimicrobial, and installed a vapor barrier and dehumidifier desiccant. Clearance testing came back clean. The job took three days, and the crawl space has stayed dry through two subsequent springs.

Maintenance: The dehumidifier runs on a humidistat and needs a filter change every six months. We also recommended improving exterior drainage on the north side of the house, which was the original water source.

Before

A roof leak around a vent pipe dripped slowly for weeks before the homeowner noticed a ceiling stain. By then, mold had spread across about 80 square feet of attic sheathing, and the insulation below was wet and contaminated.

After

We removed the wet insulation, treated the sheathing with antimicrobial, and ran HEPA scrubbers. The roofer fixed the vent pipe leak before we closed the job. Clearance testing confirmed the air was clean. Total time on site was two and a half days.

Maintenance: We recommended an annual attic inspection in the fall, before snow season. Catching a slow roof leak early is the difference between a $500 repair and a $5,000 mold job.

Mold problems we solve for Boise homeowners

Most mold calls fall into a handful of patterns. Here are the ones we see most in Boise and how we handle them.

Problem

Hidden mold behind drywall after a slow leak

By the time you see a stain or smell something musty, the mold has usually been growing for weeks. Drywall and insulation stay wet, and spores spread into the room every time the HVAC runs.

Our Fix

We use thermal imaging and a borescope camera to find the growth without cutting exploratory holes. Once located, we cut out the affected drywall, treat the framing, and verify with air sampling. Most jobs like this finish in one to two days.

Problem

Crawl space mold from wet springs and poor drainage

Crawl space mold spreads to joists, subfloor, and insulation. It can push musty odors into the living space and, in bad cases, compromise the wood structure over time.

Our Fix

We remove the growth, replace contaminated insulation, and treat the framing. Then we install a vapor barrier and a dehumidifier desiccant to keep the space dry. Crawl space jobs typically run two to three days and include clearance testing.

Problem

Attic mold from a roof leak or poor ventilation

Attic mold often goes unnoticed until it spreads across the sheathing. Wet insulation loses R-value, and the mold can eventually affect ceiling drywall below.

Our Fix

We inspect the attic with moisture meters and thermal cameras, test for species, then remove contaminated insulation and treat the framing. If the roof is still leaking, we refer you to a roofer before we finish. Clearance testing confirms the air is clean.

Problem

Bathroom mold from poor ventilation

Bathroom mold keeps coming back because the moisture source, usually a weak or missing exhaust fan, is never fixed. Grout, caulk, and ceiling corners stay damp and regrow within months.

Our Fix

We remove the growth, treat the surfaces, and check the exhaust fan's CFM rating against the room size. If it is undersized, we recommend an upgrade. That one fix is usually the difference between a one-time cleanup and a recurring problem.

Problem

HVAC mold contamination spreading through the house

Mold inside an air handler or ductwork spreads spores into every room every time the system runs. Occupants notice musty odors and worsening allergies, but the source is invisible.

Our Fix

We inspect the air handler, coils, and ductwork for growth and moisture. If mold is present, we seal the system, clean the components, and verify with air sampling. HVAC jobs take longer because the whole system has to be brought back to a clean state.

Why Boise homeowners call us for mold work

Why Boise homeowners call us for mold work

Mold is a moisture problem wearing a fungus costume. Fix the water, remove the growth, verify the air, and you are done. Here is what that looks like when we run the job.

  • We find the water source

    Removing mold without fixing the leak is a callback waiting to happen. We use a Protimeter moisture meter and Flir thermal imaging camera to trace hidden moisture behind drywall, under sinks, and inside crawl spaces. On a typical Boise Bench job, that takes 45 to 90 minutes and saves you from tearing out the wrong wall.

  • Containment keeps spores contained

    Disturbing mold without containment spreads spores through the whole house. We build 6-mil poly barriers, run negative air pressure with HEPA filters, and seal HVAC registers before demo starts. That is how we keep a basement job in the Highlands from turning into a first-floor problem.

  • Verification before we leave

    We do not call a job done because the wall looks clean. Post-remediation verification with an Air-O-Cell spore trap cassette and particle counter confirms indoor spore counts are at or below outdoor baseline. You get the lab report. If numbers are high, we keep working at no extra charge.

  • Safe for families and pets

    We use EPA-registered antimicrobial solutions and HEPA-filtered equipment, and we seal off work zones so kids and pets stay out of the dust. Most residential jobs are livable during the workday. If you need safe mold removal for families Boise Idaho, ask us about scheduling around school pickups and nap times.

Frequently asked questions about mold removal in Boise

Real answers to the questions we hear most often from local homeowners and property managers.

How do professionals remove mold in Boise ID?
Professionals remove mold in Boise ID by sealing the work area with negative-air containment, running HEPA air scrubbers, and physically removing contaminated materials like drywall, insulation, and carpet padding. Framing and hard surfaces get scrubbed and treated with antimicrobial solutions. After removal, we verify with air sampling and a particle counter. The whole process follows the IICRC S520 standard, and most residential jobs take one to three days.
Can I remove mold myself in Boise Idaho?
You can handle small surface mold on tile or glass with a household cleaner, but anything larger than about 10 square feet, or any growth inside a wall cavity or crawl space, needs professional containment. Disturbing mold without HEPA filtration spreads spores through the house. If you smell a musty odor but cannot see growth, that is also a sign to call us. We can test the air and tell you whether it is a real problem or not.
How much does mold removal cost in Boise ID?
Most residential mold removal jobs in Boise run $1,200 to $6,500 depending on square footage, location, and materials affected. A small bathroom patch might be $1,200 to $2,000. A full crawl space with contaminated insulation typically runs $3,500 to $6,500. Attic jobs with roof leak damage often land in the $2,500 to $5,000 range. We quote a flat price after inspection, so you know the number before we start.
What kills mold permanently in Boise Idaho?
Nothing kills mold permanently if the moisture source stays. The permanent fix is removing the contaminated material, treating the framing with an EPA-registered antimicrobial, and eliminating the water that fed the growth. In Boise, that usually means fixing a roof leak, repairing a supply line, or adding ventilation and a dehumidifier to a crawl space. Once the moisture is gone, mold cannot regrow. We verify with clearance testing before we close the job.

Related services

Mold Inspection

Before any mold removal Boise ID work starts, we inspect the property with moisture meters and thermal cameras to map where growth is hiding. This is the step that tells us whether you need a small patch removal or a full crawl space job.

View Mold Inspection

Mold Testing

Air and surface testing confirms what kind of mold you have and how far spores have spread. We use SKC pumps and Air-O-Cell cassettes, with lab results in 24 to 48 hours. Testing before removal prevents tearing out materials that do not need to come out.

View Mold Testing

Air Quality Testing

Indoor air quality testing establishes a baseline before and after mold removal. We compare indoor spore counts to outdoor levels using a particle counter and spore trap slides. If you have allergies or asthma, this is the report that tells you whether the air is safe.

View Air Quality Testing

Black Mold Inspection

Black mold (Stachybotrys) needs a targeted inspection because it grows slowly on wet cellulose and often hides behind drywall. We use borescope cameras to look inside wall cavities without demo, then test to confirm species before recommending black mold removal Boise ID work.

View Black Mold Inspection

Toxic Mold Testing

Some molds produce mycotoxins that affect health at low concentrations. Toxic mold testing identifies species and toxin-producing strains through lab culture. If your family has unexplained symptoms, this test gives you answers before we scope any removal work.

View Toxic Mold Testing

Mold Remediation

Remediation is the full scope: containment, removal, treatment, and clearance. Our mold remediation crews follow IICRC S520 and handle everything from a single bathroom to a whole-house job. Most Boise remediation projects finish in one to three days.

View Mold Remediation

Get mold removal Boise ID scheduled today

If you are seeing black spots, smelling something musty, or just had a leak, do not wait. Mold spreads fast in the first 48 hours. Call us at (866) 896-8166 and we will schedule an assessment, often the same day. Flat pricing, lab-verified results, and a warranty on every job.

Call now Schedule assessment

Contact Boise Mold Testing

Ready to schedule an inspection or have questions about mold testing? Call us at +1 866-896-8166 or email info@boisemoldtesting.com. We answer calls 24/7 for emergencies and schedule same-day appointments whenever possible. Our team serves all of Boise and Ada County, including ZIP codes 83702, 83703, 83704, 83705, 83706, and 83709.

Or call us right now at +18668968166 — we answer.

Boise Mold Testing


  • Phone

    +18668968166
  • Address

    Boise, Idaho

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote