Logo
Get Estimate

Bathroom mold inspection Boise ID that finds the source, not just the stain

Thermal imaging, moisture meters, and lab testing for Boise bathrooms


If you have spotted black speckling along the caulk line or a musty smell that will not quit, a bathroom mold inspection Boise ID homeowners call us for gets to the bottom of it. We check the shower pan, the drywall behind the tile, the exhaust fan, and the subfloor with moisture meters and a thermal imaging camera. You get a written report with lab results, not a guess.

Spacious modern bathroom with contemporary design elements including a large bathtub and elegant fixtures.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed Workmanship Guaranteed in Boise

What is included in a bathroom mold inspection

Every bathroom mold inspection we do includes a visual survey, moisture readings, thermal imaging, and at least one lab sample. If you need additional sampling, borescope access, or a full-home inspection, we quote that up front so there are no surprises.

Visual and moisture survey

We inspect the shower, tub, toilet, vanity, ceiling, floor, and exhaust fan. Moisture readings are taken at every suspect point with a calibrated Protimeter meter. You get a map of where the moisture is and how wet the materials are.

Thermal imaging scan

A Flir thermal imaging camera scans the walls and floor for temperature differences that indicate trapped moisture behind tile or drywall. This is how we find hidden mold behind drywall without cutting the wall open.

Air and surface sampling

We run an SKC air sampling pump with an Air-O-Cell spore trap cassette inside the bathroom and in a control room. Surface samples go on swabs or tape lift kits. Samples ship to an accredited lab the same day.

Written report with lab results

You get a report with photos, moisture readings, spore counts, species identification, and a recommended scope of work. It is formatted for insurance claims and real estate transactions. Results come back in 24 to 48 hours.

Ventilation and humidity check

We measure exhaust fan airflow and room humidity with a hygrometer. If the fan is undersized or venting into the attic, we document it. Poor ventilation is the most common cause of bathroom mold in Boise homes.

Walkthrough and recommendations

We walk you through the findings on site or by phone and answer your questions. You get a clear picture of what is cosmetic, what needs remediation, and what you can do yourself to prevent it from coming back.

What a bathroom mold inspection Boise ID actually involves


A bathroom mold inspection Boise ID is a room-by-room evaluation that combines moisture readings, thermal imaging, and air or surface sampling to confirm whether mold is present, what species it is, and where the water feeding it comes from. We do not just look at the visible spot on the ceiling. We pull the toilet, check the wax ring, inspect the shower pan from the access panel, and run a borescope camera inside the wall cavity behind the tile. If the exhaust fan moves less than 50 CFM, that gets flagged too, because poor ventilation is the number one driver of bathroom mold in Boise homes.

Boise's dry summers do not protect you indoors. A bathroom is a wet room 365 days a year, and our cold winters make it worse: warm shower air hits a cold exterior wall, condenses inside the cavity, and feeds mold you never see. We routinely find hidden mold behind drywall in older North End and Depot Bench homes where a 1970s exhaust fan has been venting into the attic for decades. If you have had a supply line leak or a toilet overflow, a bathroom mold assessment in Boise Idaho should happen within 48 hours, not next month.

How our bathroom mold inspection process works

From the first phone call to the final report, here is exactly what happens when you book a bathroom mold inspection with us in Boise.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and methods we use on every inspection

Tools & Equipment

Protimeter moisture meter

Pin and pinless readings on drywall, tile, grout, and subfloor to measure how wet materials are and how far moisture has spread.

Flir thermal imaging camera

Detects temperature differences behind walls and floors that indicate trapped moisture or missing insulation, without cutting into finishes.

Borescope camera

Inserted through a small access hole to visually inspect inside wall cavities, behind shower pans, and under subfloors.

SKC air sampling pump with Air-O-Cell cassette

Draws a calibrated volume of air through a spore trap cassette to capture airborne mold spores for lab analysis.

Swab and tape lift kits

Collect surface samples from visible growth for species identification and to confirm whether the growth is active.

Extech hygrometer

Measures relative humidity and temperature in the bathroom to assess ventilation effectiveness and condensation risk.

Dylos particle counter

Provides real-time particulate readings to identify elevated airborne particles during the inspection.

Methods & Standards

IICRC S520 mold assessment standard

We follow the IICRC S520 standard for mold assessment, which defines how to inspect, sample, and document mold conditions. It is the industry benchmark and it is what insurance adjusters and remediators expect to see in a report.

Moisture mapping

We take moisture readings at consistent points across the bathroom and record them on a floor plan. This shows the extent of moisture and gives you a baseline to compare against after drying or remediation.

Air sampling with control comparison

We sample the bathroom and a control room outside it. Comparing spore counts tells us whether the bathroom is a source of contamination or whether the whole house is affected.

Borescope cavity inspection

When thermal imaging flags a suspect area, we drill a small access hole and run a borescope camera inside. This confirms hidden mold behind drywall without demolition.

Post-remediation verification

After remediation, we re-sample the area and compare spore counts to the pre-remediation baseline. This confirms the cleanup worked and gives you documentation for insurance or resale.

When to book a bathroom mold inspection in Boise

01

You just bought a home and the inspection report flagged moisture in the bathroom.

What we do: We do a full bathroom mold inspection with thermal imaging, moisture readings, and air sampling. If the moisture is from a slow leak, we document it. If mold is present, we identify the species and give you a scope for negotiation or repair.

→ You get a clear picture of what you bought and what it will cost to fix, before you close.

02

You had a toilet overflow or supply line burst and the floor is dry but smells musty.

What we do: We inspect the subfloor and the wall cavity behind the toilet with a moisture meter and borescope. If mold has started, we sample it. If the area is still wet, we document the moisture so you can get it dried properly.

→ You know whether the leak caused mold and whether the drying was complete.

03

Your bathroom exhaust fan is old, noisy, or vents into the attic.

What we do: We measure fan airflow and check where it terminates. If it is venting into the attic, we document it and check the attic for mold growth. We also measure room humidity to see how bad the moisture load is.

→ You get a clear recommendation on the fan upgrade and any attic cleanup needed.

04

Someone in the house has new allergy or respiratory symptoms and you suspect mold.

What we do: We run air sampling in the bathroom and a control room to compare spore counts. If the bathroom is elevated, we inspect further. If the whole house is elevated, we recommend a full-home mold inspection.

→ You know whether the air quality in your home is affected and what to do about it.

05

You had mold removed before and it is coming back.

What we do: We inspect the area, check moisture levels, and sample the new growth. If the moisture source was never fixed, we identify it. If the previous removal was incomplete, we document that too.

→ You get a prevention plan that addresses the root cause, not just the visible mold.

How bathroom mold inspection runs in Boise

Boise has a dry climate, but that does not make bathrooms safe. Our cold winters are the real problem: warm, humid shower air hits a cold exterior wall and condenses inside the cavity, feeding mold where you cannot see it. Older homes in the North End, Depot Bench, and Vista Neighborhood often have original exhaust fans that move less than 50 CFM or vent straight into the attic. Newer builds in Harris Ranch and Southeast Boise have tighter envelopes, so we watch for condensation on cold walls and undersized fans that were never upgraded. We also see a spike in calls after hard freezes when supply lines crack, and after spring rain when roof leaks show up in bathroom ceilings. If you are searching for a bathroom mold assessment in Boise Idaho, we are probably already working in your neighborhood this week. We serve all of Ada County and the 83702, 83703, 83704, 83705, 83706, and 83709 ZIP codes.

Neighborhoods We Serve

  • North End

    Older bungalows with original plumbing and exhaust fans that vent into the attic. Bathroom mold here is often decades old and hidden behind tile.

  • Harris Ranch

    Tighter, newer construction with cold exterior walls. We see condensation-driven mold on the north-facing bathroom walls.

  • Depot Bench

    Mix of mid-century homes with small bathrooms and undersized fans. Moisture buildup is common after a shower.

  • Boise Bench

    Many homes have had bathroom remodels that covered up old water damage. We check behind new tile for hidden mold.

  • Southeast Boise

    Newer builds with master baths that have large tile showers. We watch for failed shower pan seals and slow drain leaks.

Local Conditions We Plan For

  • Cold winters and warm shower air

    Condensation forms inside exterior wall cavities during winter, feeding mold behind the tile. This is the most common hidden mold scenario we find in Boise.

  • Dry summers with low indoor humidity

    Mold growth slows in summer, so problems can go unnoticed until the first cold snap. We often find mold that started the previous winter.

  • Hard freezes that crack supply lines

    A cracked supply line behind a vanity can leak for weeks before you notice. We see a spike in bathroom mold calls after every hard freeze.

  • Spring rain and roof leaks

    Roof leaks show up as ceiling stains in bathrooms. If the leak has been slow, mold can be growing in the ceiling cavity for months.

Hidden mold behind a North End shower wall

Before

A homeowner in the North End had a musty smell in the hall bathroom for months. No visible mold. The exhaust fan was original and venting into the attic. Moisture readings were elevated along the shower wall, but the tile looked fine.

After

Thermal imaging flagged a cold zone behind the shower wall. A borescope confirmed mold growth on the back of the drywall. Lab results showed Cladosporium and a small amount of Stachybotrys. The wall was opened, remediated, and the fan was replaced with a 110 CFM unit venting outside.

Maintenance: Run the new fan for 20 minutes after every shower and check the attic annually for any sign of moisture. Keep indoor humidity below 60%.

Before

A Harris Ranch homeowner noticed a musty smell near the master bath toilet. The floor felt solid, but the base of the toilet had a dark ring. The home was five years old and the wax ring had failed.

After

Moisture readings showed the subfloor was wet in a 3-foot radius around the toilet. Air sampling confirmed elevated spores. The toilet was pulled, the wax ring replaced, and the affected subfloor section was removed and replaced. Post-remediation testing showed spore counts back to normal.

Maintenance: Check the toilet base every six months for wobble or staining. Replace wax rings every 10 to 15 years, or any time the toilet is pulled.

Before

A Depot Bench homeowner called about a musty smell in the hallway. The bathroom fan was working, but the attic above it was damp. The fan was venting directly into the attic insulation.

After

Attic inspection found mold growth on the roof sheathing above the bathroom. Lab testing confirmed Aspergillus and Penicillium. The fan was re-ducted to vent through the roof, the affected sheathing was treated, and the attic was dried. Follow-up testing showed normal spore levels.

Maintenance: Verify your bathroom fan vents outside, not into the attic. Check the roof vent annually for blockages and have the attic inspected every two years.

Bathroom mold problems we solve in Boise

Most bathroom mold calls fall into a handful of patterns. Here are the ones we see most often in Boise homes and how we handle them.

Problem

Musty smell but no visible mold

The smell means mold is growing somewhere you cannot see, usually inside the wall cavity or under the floor. Ignoring it lets the colony spread and can affect the air in adjacent rooms.

Our Fix

We use thermal imaging and a borescope camera to find the hidden growth without tearing the room apart. Once we locate it, we sample to confirm species and moisture source, then give you a scope for removal.

Problem

Black speckling along caulk and grout

Surface mold on caulk is often the visible tip of a bigger problem. If the caulk is failing, water is getting behind it and feeding mold in the wall or subfloor.

Our Fix

We check moisture behind the caulk line with a meter and inspect the wall cavity with a borescope. If the growth is surface-only, we tell you. If it has spread, we document it and recommend the right level of removal.

Problem

Mold after a toilet or supply line leak

Mold can start growing within 24 to 48 hours of a leak. By the time you notice the smell, the colony is often established in the subfloor or the wall behind the toilet.

Our Fix

We inspect the leak area, map moisture with a meter and thermal camera, and sample the air. If the leak was recent, we tell you what can be dried versus what needs removal. If it is older, we scope the remediation.

Problem

Recurring mold after a previous cleanup

Mold comes back when the moisture source was never fixed. Cleaning the visible growth without addressing the leak or ventilation just resets the clock.

Our Fix

We trace the moisture source first, then sample to confirm the species. If the exhaust fan is undersized or venting into the attic, we document it. You get a prevention plan along with the inspection report.

Problem

Mold near the HVAC return

If the bathroom is near an HVAC return, spores can cycle through the whole house. That turns a one-room problem into an air quality issue for the entire home.

Our Fix

We sample the bathroom and a control room to compare spore counts. If the HVAC system is affected, we recommend HVAC mold inspection and duct cleaning before anyone uses the system again.

Why Boise homeowners book this inspection

Why Boise homeowners book this inspection

Mold in a bathroom rarely stays in the bathroom. It spreads into the wall cavity, the subfloor, and sometimes the HVAC system. Here is what a proper inspection gets you.

  • Find the water source

    Mold needs moisture, so killing the mold without fixing the leak is wasted money. We trace the source with a Protimeter moisture meter and a Flir thermal imaging camera, checking the shower pan, toilet base, supply lines, and exterior wall cavity. You get the exact location of the leak, not a vague 'somewhere behind the tile' answer.

  • Know your mold species

    Not all mold is black mold. We collect air samples with an Air-O-Cell spore trap cassette and surface samples with swabs and tape lifts, then send them to an accredited lab. The report tells you whether you are dealing with common Cladosporium or something more serious like Stachybotrys, which changes how the job gets handled.

  • Protect your family's air

    Bathroom mold releases spores every time someone runs the shower. If your HVAC return is near the bathroom door, those spores cycle through the whole house. A bathroom mold assessment in Boise Idaho gives you documented spore counts so you know whether the air in your living room is affected or the problem is contained to one room.

  • Get a scope you can hand to a contractor

    Our written report includes photos, moisture readings, lab results, and a clear scope of work: what needs to come out, what can be cleaned, and what needs a HEPA vacuum and antimicrobial treatment. Contractors bid from it. Insurance adjusters accept it. You are not stuck relaying information secondhand.

Mold inspection expertise you can verify

Our inspectors hold IICRC WRT and IICRC AMRT credentials, which cover water damage restoration and mold remediation standards. We also carry ACAC CMI and CMR certifications, and we follow the IICRC S520 standard for mold assessment. That matters because Idaho does not license mold inspectors at the state level, so anyone with a flashlight can call themselves one. We use calibrated equipment from Protimeter, Extech, and Flir, and we send every sample to an accredited third-party lab. Our reports are written to hold up with insurance adjusters and real estate transactions across Ada County.

  • IICRC WRT and AMRT certified, with training in water damage restoration and mold remediation standards.
  • ACAC CMI and CMR credentials for mold inspection and remediation oversight.
  • Calibrated Protimeter and Extech moisture meters, plus Flir thermal imaging on every inspection.
  • Lab analysis through accredited partners using Air-O-Cell spore trap cassettes and culture media.
  • Written reports formatted for insurance claims and real estate transactions in Ada County.
Get Started Today
Mold inspection expertise you can verify

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

How do I get rid of bathroom mold in Boise ID?
You fix the moisture source first, then remove the mold. Bleach sprays only kill surface mold and leave the roots in the drywall or grout. For anything larger than a dinner plate, or any mold behind the tile, you need a HEPA vacuum, antimicrobial treatment, and often removal of the affected drywall. Start with a bathroom mold inspection Boise ID to confirm the species and the moisture source before you spend money on removal.
What causes bathroom mold in Boise Idaho?
Poor ventilation is the top cause in Boise. If your exhaust fan moves less than 50 CFM, or if it vents into the attic instead of outside, moisture stays in the room. Other common causes include a slow toilet leak at the wax ring, a shower pan that was not sealed properly, a supply line drip behind the vanity, and cold exterior walls that condense warm shower air inside the cavity during winter.
How much does bathroom mold inspection cost in Boise ID?
Most bathroom mold inspections in Boise run $250 to $550 in 2026, depending on how many samples you need and how hard the problem area is to access. A basic visual and moisture inspection with one air sample sits at the low end. If we need thermal imaging, a borescope, and multiple surface samples, expect the higher end. You get the price before we start.
Is bathroom mold dangerous in Boise Idaho?
It depends on the species and how much of it there is. Common bathroom molds like Cladosporium and Aspergillus cause allergy symptoms, coughing, and sinus issues in sensitive people. Black mold (Stachybotrys) and toxic mold that produce mycotoxins are more serious and need prompt removal. Lab testing is the only way to know which one you have, which is why we sample rather than guess.

Book your bathroom mold inspection Boise ID today

If you see mold, smell mold, or just had a leak, do not wait for it to spread. We are licensed, insured, and we show up when we say we will. Call us and we will get an inspector to your door, often the same day.

Call Now Schedule Inspection

Contact Boise Mold Testing

Ready to schedule an inspection or have questions about mold testing? Call us at +1 866-896-8166 or email info@boisemoldtesting.com. We answer calls 24/7 for emergencies and schedule same-day appointments whenever possible. Our team serves all of Boise and Ada County, including ZIP codes 83702, 83703, 83704, 83705, 83706, and 83709.

Or call us right now at +18668968166 — we answer.

Boise Mold Testing


  • Phone

    +18668968166
  • Address

    Boise, Idaho

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call +18668968166 Get Quote
Call Quote